20 Myths About Upvc Window Replacement Hinges: Busted

Choosing Upvc Window Replacement Hinges

It's not as difficult as it might appear to select and install upvc replacement hinges. Check that the hinges' arrows are facing the correct direction and then measure the thickness of the hinge arms on the frame opening (13mm or17mm).

There are a few different kinds of hinges to pick from, each one with distinctive characteristics. This article will focus on the most popular kinds of uPVC window hinges, and their benefits.

Egress/Easy Clean Hinge

These windows are an excellent choice for replacing or upgrading your fire escape window since they open up to a full 90 degree angle. They can be closed to a 'easy-clean' position that allows you to see the outside of windows without the need to climb ladders or lean at risky angles.

These heavy duty egress hinges are manufactured by Yale one of the most popular and trusted home security brands available today. These hinges are suitable for any kind of uPVC side-hung window. By pressing a tiny button, the window sash is slid to the side and into the easy-cleaning position. After closing, the window sash will be returned to its original position.

Both 13mm and 17mm are both available. Based on the size of your existing window, we recommend using our Egress Selection Guide to determine the best product for you.

The hinges are designed to be used with a standard side-hung frame that is made of aluminium or uPVC. They are equipped with an easy friction screw that can adjust the amount of resistance that is generated. This makes it easier to open the window and reduces the possibility of an accidental closure in high winds. They have been cycle tested to over 30000 cycles and comply with BBA/Secured by Design and British Standards approved BS EN 13126-6:2008.

There are no buttons or catches There are no buttons or catches. Nico Egress Easy Clean Friction Hinge is simple to use and offers a practical solution to emergency egress as well as safe cleaning. First, open the door to the egress (full opening) position and then press the hinge retaining clip located on the inside of the bottom corner. This will release both the catches on the top and bottom and allow you to slide the sash to the clean position. Close the window once you have the sash in the easy-cleaning position. This will reset the hinges to their exit positions.

Fire-Escape Hinge

Fire Escape Hinges (also called "Easy Clean") are used to replace windows that open sideways for fire safety reasons. These hinges permit a larger opening in the event of fire. The building regulations state that this kind of hinge should be placed in any space that is habitable and has a window.

The windows feature an elongated friction that permits the windows to open up to 90 degrees. They also let the opening sash to slide across the glass when opened, allowing for easy cleaning without the need to climb ladders. The hinges are simple to operate and do not have complicated buttons or catches. They can be operated from inside of the house using an easy, safe lever.

The hinges are manufactured in the UK by Cotswold and come with a child safety limiter for use throughout the day which can be turned off with a hidden button providing you with peace of mind that your children won't accidentally open the door too far. The stack heights are 13mm or 17mm.

To order these hinges, simply measure the length of your existing side-hung window hinge that is fixed to the frame (see the guidelines for measuring your upvc window hinges). Choose the right size hinge from the list below.

It is important to note that this measurement is taken from the part of the hinge that connects to the frame, not the sash. The actual hinge length may be shorter or longer depending on the way your old windows were manufactured. When choosing the width of your hinge, most upvc windows will fit a 13mm stack height. However, should your window frame is 17mm wide, you should select the option that fits this. Alternately, you can install the 4mm packer to make up the difference. All hinges are supplied with two hands (1 left and one right). Screws are not included in the hinges. They can be purchased separately if required. We suggest using our upvc window hinge repair screws. They are specially made to improve the performance of your hinges, allowing them to operate efficiently for a longer. They have a reduced-friction design and a heightened weather seal with an encapsulated nylon reducer cap.

Restricted Hinge

There are occasions windows need to fully open and this can be a challenge using a standard hinge. These restricted child safety friction hinges can help overcome this issue and provide a solution for situations where ventilation is required but access for cleaning or escape in the case of fire is not possible. They work by restricting the amount the sash can open and allowing the override of this restriction with the push of a button. They work with both side- and top-hung windows and are available in 17mm and 13mm stack heights.

The Nico Restricted Egress Hinges combine the features of both a standard restrictor, and an escape pivot to provide a simple but efficient way to meet building regulations. It is suitable for side-hung and top opening upvc door hinges replacement windows and is available in 17mm and 13mm stack heights. It is available in a pair, where one hinge is restricted egress and the second is unrestricted allowing one of these to be placed on the lower part of the sash, while the other is attached to the top.

These uPVC hinges are designed to be used on windows that aren't able to be fully opened, like a child's bedroom. The mechanism restricts the amount the sash can open to 100mm for safety and re-engages once the window is closed.

Like the other kinds of uPVC friction hinges, these can be used on all types of windows handles and hinges are perfect for hard to reach windows above the ground, three-storey flats or those that typically require a ladder to reach them. They can be complemented with our selection of security enhancements like hinge guards and protection plates, or dog bolts to offer PAS 24 performance.

It is crucial to take measurements of the hinge on your current window in order to get replacements that are the same size. The most efficient method to do this is by viewing the hinge in the image gallery and working out where you want it to be placed. The top-hung hinges can only be placed on one side, while the side hung hinges can only be placed on one side.

Standard Hinge

Standard hinges use metal-to-metal connections and do not require additional components to reduce friction. It is available in many finishes and also has a fire rating. To quickly determine the radius of hinges, lay it out flat and align a quarter and dime in two corners. If the quarter fits better, then the corner should be round to 5/8 inches.

Selecting the right hinge can determine the success or failure of your door's appearance. It's important to match the finish and style of your door with the hinges to create a seamless look that's both practical and visually attractive.